SIMUFLY.COM Discussion Forums

SIMUFLY.COM Discussion Forums
https://www.simufly.com/cgi-bin/yabb2/YaBB.pl
Delco Carousel IV-A INS For Microsoft Flight Simulator >> Delco Carousel IV-A INS For Microsoft Flight Simulator >> Everything freezes
https://www.simufly.com/cgi-bin/yabb2/YaBB.pl?num=1187633582

Message started by skipper on Aug 20^th, 2007, 7:13pm

Title: Everything freezes
Post by skipper on Aug 20^th, 2007, 7:13pm

Could anyone get me out of my frustration? By the time I enter all the waypoints in the INS, all my commands freeze on the a/c, except for the power levers. :'(
Thank you for your help in advance.

Title: Re: Everything freezes
Post by Marco Ravanello on Aug 21^st, 2007, 9:01am

What do you mean with "all my commands freeze"? Could you provide more details?
Did you enable the Keyboard Capture mode on the CDU and then forgot to turn it off?

Regards
Marco

Title: Re: Everything freezes
Post by skipper on Aug 21^st, 2007, 10:31am

Marco, I was attempting to do my first Tutorial Flight. I had the LAT/LONG displayed on top of the cockpit by using Shift+Z.
During this time I was inserting all the waypoints as instructed in the tutorial. When finished, I could not cancel Shift+Z, minimize Carousel, change views or even ESC from FS. I actually had to do a Control Alt Del to start my FS up again from scratch.
Regards,
Nick aka skipper
PS. also during these inserts the INS was in Align mode, but never had the green light coming up. The 15 minutes were way over by this time.

Title: Re: Everything freezes
Post by Marco Ravanello on Aug 21^st, 2007, 1:43pm

Question: To enter all waypoints coordinates did you enable the "Keyboard Capture Mode" by pressing the upper left screw of the CDU, so that you can enter them by typing on the keyboard numeric pad, or did you enter them with the mouse clicking on the CDU "keys"?

Title: Re: Everything freezes
Post by skipper on Aug 21^st, 2007, 3:44pm

Hi Marco,
No...I was entering all way points with the mouse and by the panel on the INS.
Today, I have decided to go an other way and copied the panel.cfg from the 737 sample in the program and pasted it into the MS 737....still no green light, but at least nothing frozen. When I inserted all the way points, I even shut the engines down, but on the flight out from Boston my pos'n was nothing like I should have had. I was forced to navigate by the GPS. Sorry to be such a pain in the "proverbial"...lol
Thanks for your concern already.
Nick

Title: Re: Everything freezes
Post by skipper on Aug 21^st, 2007, 3:59pm

BTW....after more than 20 minutes of "align" still no green light.

Title: Re: Everything freezes
Post by Marco Ravanello on Aug 21^st, 2007, 4:29pm

For the "alignment problem" see https://www.simufly.com/cgi-bin/yabb2/YaBB.pl?num=1180905920

Regards
Marco

Title: Re: Everything freezes
Post by skipper on Aug 22^nd, 2007, 8:16am

Thank you Marco, I will try and get back to you. :)

Title: Re: Everything freezes
Post by skipper on Aug 22^nd, 2007, 10:04am

Hello Marco,
Well I have tried to align the INS in the VC10 as well as the standard 737. The following has happened.
I went through the first few paragraphs of the Tutorial Flight...up till the alignment stage.
VC 10
Pos....set in ramp position on both units
CDU set to DSRTK/STS on both units
MSU set to Align
Read out as follows
First window 0 degrees
Second window 002 95 these read outs on both units
No visible alignments at all.
After 15 mins I pressed the fast align screw on both MSU's...no effect..no magic green light.

I have tried the same thing in the 737

on the alignment stage the windows showed the following.

First window 0 degrees
Second window 006 95
After a little while the 006 went down to 002, but no further. Still no magic green light after about 20 minutes.

I must be dense or something. (I am crying for the old days of the ASN42 system in the P3 Orions....lol)

Title: Re: Everything freezes
Post by Marco Ravanello on Aug 22^nd, 2007, 11:21am

If engines have already been started then make sure they're idle (press F1) and check Parking Brakes are SET
Turn ON all INS units by moving the MSU Mode Selector knob into the STBY position

a) Enter the present position on ALL units
b) Move MSU Mode Selector to ALIGN
c) CDU Data Selector to DSRTK/STS
d) Check (and CLEAR) any pending Action and Malfunction Codes (see CIVA/Docs/DisplayedStatus.pdf!!)

The green light will illuminate, this is guaranteed! :-)

So I think you're doing something wrong.

You wrote "Second window 002 95" (please use the correct terminology, that "second window" is in fact the "right data display").
Well the "02" is an Action Code (again read CIVA/Docs/DisplayedStatus.pdf and CIVA/Docs/ActionAndMalfunctionCodes.pdf) which should NOT be there. You're not reporting which was the associated Malfunction Code so I can't tell you what happened.

Please read the manuals, you will not be able to use the INS if you try to learn it by practice only.

Regards
Marco

Title: Re: Everything freezes
Post by skipper on Aug 22^nd, 2007, 5:08pm

Hi Marco, I am sorry I have not used the correct terminology. On the subject of reporting, I have written down for you exactly what was shown on the display. Anyway, back to the books and we shall see what will happen.
Thank you for your help.
Regards,
Nick

Title: Re: Everything freezes
Post by skipper on Aug 22^nd, 2007, 6:42pm

Thank you Marco, it sure worked, now for the real learning to start.